We are professional manufacturer of alumina ceramic products.
We have focused on ceramic products for more than 20 years since year 1994.
Our ceramic products include ceramic insulator, ceramic pipe/tube,ceramic rod, textile ceramics,etc.
If you have any inquiry,please offer drawing, sample or dimension.
We can customise it for you and choose the best suitable material for your request and application.
Parameters of alumina ceramics:
Â
| Material | Unit | Steatite ceramics | 95% alumina ceramics | 99.5% alumina ceramics |
| Density | G/cm3 | 2.7 | 3.65 | 3.85 |
| Highest application temperature | °C | 1100 | 1500 | 1800 |
| Bending strength | Mpa | 150 | 300 | 340 |
| Compressive strength | Mpa | 900 | 3400 | 3600 |
| Hardness | HV0.5 | 800 | 1800 | 2000 |
| Insulation breakdown strength | KV/mm | 10 | 15 | 18 |
| Accuracy of working(mm) | ||||
| Perpendicularity | 0.01 | |||
| Concentricity | 0.01 | |||
| Roundness | 0.005 | |||
| Straightness | 0.005 | |||
| Parallelism | 0.01 | |||
| Planeness | 0.005 | |||
| Roughness | 0.05 | |||
| Fit clearance | 0.005 | |||
Ceramic eyelet apply to the coiling machine and spinning and weaving machinery, is in common use fault silk another piece, is used to demand no high fault silk occasion. Silk thread slides when the job, in China eye outside, for reducing friction, must raise material hardness, smoothness and form. Our company selects and uses 99%'s Al2O3, hardness greater than HRa88, density 3.85, surpasses essence throwing Ra0.2. Introduction:
We are professional manufacturer of alumina ceramic products.
We have focused on ceramic products for more than 20 years since year 1994.
Our ceramic products include ceramic insulator, ceramic pipe/tube,ceramic rod, textile ceramics,etc.
If you have any inquiry,please offer drawing, sample or dimension.
We can customise it for you and choose the best suitable material for your request and application.
Parameters of alumina ceramics:
Â
| Material | Unit | Steatite ceramics | 95% alumina ceramics | 99.5% alumina ceramics |
| Density | G/cm3 | 2.7 | 3.65 | 3.85 |
| Highest application temperature | °C | 1100 | 1500 | 1800 |
| Bending strength | Mpa | 150 | 300 | 340 |
| Compressive strength | Mpa | 900 | 3400 | 3600 |
| Hardness | HV0.5 | 800 | 1800 | 2000 |
| Insulation breakdown strength | KV/mm | 10 | 15 | 18 |
| Accuracy of working(mm) | ||||
| Perpendicularity | 0.01 | |||
| Concentricity | 0.01 | |||
| Roundness | 0.005 | |||
| Straightness | 0.005 | |||
| Parallelism | 0.01 | |||
| Planeness | 0.005 | |||
| Roughness | 0.05 | |||
| Fit clearance | 0.005 | |||
Ceramic eyelet apply to the coiling machine and spinning and weaving machinery, is in common use fault silk another piece, is used to demand no high fault silk occasion. Silk thread slides when the job, in China eye outside, for reducing friction, must raise material hardness, smoothness and form. Our company selects and uses 99%'s Al2O3, hardness greater than HRa88, density 3.85, surpasses essence throwing Ra0.2.
Continuous Waste Plastic Pyrolysis Plant
Pyrolysis Plant is used for recycling waste tire, waste plastic, waste rubber to fuel oil. According to the actual situation in every country and district, we developed different models of Batch Pyrolysis Plants for waste tires, rubber and plastic with daily capacity 25-40 tons.
Flow-chat of Continuous Waste Plastic Pyrolysis Plant
Advantages of Continuous Waste Plastic Pyrolysis Plant
1. Large daily capacity of 25 MT raw materials, and can work 24 hours without any stop for 15-20 days;
2. Auto-loading, auto-discharging and oil coming out at the same time;
3. Only need fuel for the beginning 2-3 hours, then the sync gas generates itself is enough to support heating, saving fuel cost;
4. Low requirement on the raw materials, no need tiny granule, 5cm pieces acceptable for smooth running;
5. High efficiency condensers, more oil output, good quality oil, easy to clean.
6. Sync gas recycling system, fully burned after recycling and utilization, preventing pollution and saving fuel cost.
7. National patent smoke scrubber, can efficient remove the acid gas and dust of the smoke, environmental friendly to meet related national standards.
8. Easy to operate, need less manpower.
Technical Parameter of Continuous Waste Plastic Pyrolysis Plant
|
NO. |
ITEM |
Technical Parameter |
|
1 |
Suitable Raw Materials |
Small pieces of Waste tyre,rubber, waste plastic≤5cm |
|
2 |
Operating Mode |
Fully Continuous Operation |
|
3 |
Structure |
Horizontal Type Revolve |
|
4 |
Loading and discharging |
Fully Automatic Feeding and Discharging under High Temperature at Same Time |
|
5 |
Capacity(24h) |
8-20Mt |
|
6 |
Work Pressure |
Slightly Negative Pressure |
|
7 |
Oil Yield of tyres |
40%-45% |
|
8 |
Reactor Rotational Speed |
1R/M |
|
9 |
Installation Power |
110kw |
|
10 |
Cooling Method |
Cycle water |
|
11 |
Type of Drive |
Sprocket Wheel |
|
12 |
Heating Method |
Hot Air |
|
13 |
Noise dB(A) |
≤85 |
|
14 |
Main Reactor Weight (MT) |
About 20Mt |
|
15 |
Total Weight(MT) |
About 45Mt |
|
16 |
Installation Space Required |
60m*20m |
|
17 |
Manpower |
2/shift |
|
18 |
Shipment |
5*40HC |
|
19 |
Delivery time |
≤70Days |
Continuous Waste Plastic Pyrolysis Plant
Continuous Waste Plastic Pyrolysis Plant,Continuous Plastic Pyrolysis Plant,Plastic Pyrolysis Plant
Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclings.nl