II. Function introduction (1) Management of outbound roads When a person in charge of guarding a house, such as seeking medical treatment, arraignment, courtroom, or transfer to prison, needs to go out, the person serving the sentence needs to wear an RFID wristband and install a vehicle-mounted positioning base station on a vehicle such as a prisoner. On the one hand, GPS location management of vehicles is conducted. On the other hand, the number and status of detainees inside the vehicle and the car guards are monitored. The vehicle-based positioning base station sends vehicle position and vehicle personnel information back to the monitoring center through GPRS or CDMA. The monitoring center can Keep abreast of the situation of the vehicles and the people inside the escort.
The portable prison guard carries the portable monitoring terminal with him. The terminal and the alarm monitor the status of the people in the vehicle in real time. When there is an abnormality in the wristband, an alarm is issued immediately to enable effective monitoring on the way out. At the same time, when the prison guards encounter an emergency, they can also send an alarm signal to the monitoring center.
(2) Out-going inquiries, medical treatment, labor, supervising operations outside the prison When detainees go out for medical treatment, labor, etc., they can quickly set up a temporary wireless mobile monitoring and positioning system at the place where they go, and conduct on-site monitoring of the staff who wear the wristband. To prevent the escape of a prisoner from going out. The wireless mobile monitoring base station sends on-site personnel information back to the monitoring center via GPRS or CDMA. The monitoring center can keep abreast of the situation of people going out through the monitoring terminal, and can take immediate measures when abnormal conditions occur.
Off-site executives can wear a GPS positioning wristband to monitor the position of the person and the state of the wristband in real time. When an abnormal situation occurs, an alarm message is automatically sent out.
(3) Real-time monitoring of the fixed area within the custody station The monitoring of the base station is performed at the guard house and all other relevant personnel activities and through the regional deployment of the base station, and full coverage of the signal is required in the surveillance area within the guard house. Place radio frequency fences in border areas such as fences. Relevant personnel wear positioning wristbands to conduct real-time, full-scale, active monitoring of prisoners and management personnel, and provide timely alarms for abnormal conditions. Prison guards can wear wristbands to prevent attacks and automatically or manually issue alarm distress signals in emergency situations.
(d) Management of borders and access control of the guard house By arranging the base stations at the boundary of the guard house and exit gates and defining the legal action area, coupling of radio frequency fences and wrist straps arranged at the boundary and exit gates can be used to achieve close proximity to the borders and exits. Getting started wristbands for information statistics and alarm tips.
(V) Monitoring and management of external vehicles By combining the vehicle information with the card, the position of the vehicle within the guard station can be controlled by issuing the vehicle for the day-in and day-out guard station and the escort vehicle, and the vehicle position information, personnel information, and the mobile information of the vehicle at the guard station can be controlled in real time. . In combination with the GPS system, it monitors whether the outbound vehicle's walking route is traveling in accordance with the prescribed route and controls the position and status of the outgoing vehicle in real time.
(6) The asset management can manage the defensive items and important assets of prison guards within the guard house, and can achieve the statistics of the use of defense depots, the monitoring of defensive items without leaving the posts, the maintenance records of defensive items, etc., as well as the important equipment within the guard house. Position setting and status monitor (7) Linkage management with other facilities of the guard station When an alarm occurs, it can automatically switch to the video camera near the corresponding alarm site and follow the monitoring site. At the same time, it can also cooperate with the fingerprint system and the electric door to provide signals to the follow-up door in the corresponding position to control the action of the electric door.
Third, wireless video monitoring terminal equipment:
IV Summary <br> <br> wireless technology to be widely used in the care of the security system, the cost of equipment is also an important factor, the wireless communication module for low-cost monitoring system requirements.
Nowadays, wireless network technology is introduced into the management of the management industry, and an improved application method is proposed for the comprehensive management of the detention facility, and an overall plan and design plan for the entire management system is proposed. Under the background of the informationized construction of the monitoring station, the comprehensive use of advanced wireless network technology, computer technology, network communication technology, automatic control technology, active detection technology, digital image encoding and decoding technology and multimedia technology has realized the information of the guard house. Monitor system system function requirements.
RSM series of spiral color mixer are used to mix granulated solid plastic raw material and master batch. It is a large plastic
material mixing equipment and has advantages of big capacity, low energy consumption and high working efficiency. It is an ideal auxiliary equipment for plastic extruding and injecting processing production.
Characteristics
1) Screw blades are welded onto the main axis first. Then they are processed as a whole. Therefore, with high concentricity, the machine will run very smoothly and steadily.
2) Screw blades moving in spirals and cycles makes mixing more even and quickly.3) The parts which may touch raw material are
all made of stainless steel. Easy to clean and avoid becoming rusty.
4) Small horse power, large mixing capacity, high speed, mixing in an enclosed space, even mixing, no leakage.
5) Overload protection on motor and power supply interlock protection device so that it can double protect safety of motor and
workers.
6) Grease injection device and material discharge device are installed at the bottom of machine frame. The bearings are very
durable.
Introduction:
To achieve the aim of mixing material, screw blades are used to generate vortex. Materials are sucked towards mixing screws at
the center of hopper bottom by vortex, and then materials whirl upward to the top and fall down so that the evenly mixing can be fulfilled in a short period.
Features:
All parts in contact with material are made of stainless steel to minimize material contamination.
Vertically mounted blending screw and cylinder ensure even mixing of materials.
Removable top assembly (lid, motor, and control box) for easy cleaning.
0~300 hours auto-stop function.
Equipped with main power switch and safety interlock protective device to ensure operator's safety and no damage to the machine.
Pneumatic slide gate is an optional accessory for mounting at discharge outlet.
Optional suction pipes are available for mounting at the two sides to help material conveying.
Spiral Color Mixer
Spiral Color Mixer, Color Mixer Machine, Plastic Color Mixer, Plastic Mixer
Ningbo Beilun Rhong Machinery Manufacturing Co., Ltd. , https://www.rhongmachinery.com