How is the storage capacity required for the tailings pond calculated?

Posted on

Tailings design, calculate the required storage capacity beneficiation plant life can be calculated as follows.

WN
V=———;;
Γη

Where V is the total storage capacity of the required tailings pond, m3 ;
W——the amount of tailings discharged by the ore dressing plant per year, t/year;
N——Design and production life of the concentrator, year;
γ——Tail mine bulk density (heap specific gravity), ton/ m3 , determined according to the data of similar tailings, if there is no data, refer to Table 1 for selection;
Tailings bulk density (heap specific gravity) γ Table 1
Serial number
Content of each grade of tailings (%)
γ (ton / meter 3 )
>2 mm
2~0.05 mm
<0.05 mm
1
2
3
4
5
6
7
<10
<10
<10
<10
<10
<10
<10
>0.25 mm more than 50
>0.1 mm higher than 50
>50
>40
>40
<50
<50
0~3
0~3
3~10
10~20
20~30
30~50
>50
1.6~1.75
1.55~1.65
1.5~1.6
1.4~1.55
1.2~1.4
1.0~1.2
0.8~1.0
η——The final storage capacity utilization coefficient of tailings pond is related to the shape of tailings pond, the number of tailings and the method of ore mining. The rough calculation can be selected in Table 2.
Storage capacity utilization η Table 2
Tailings shape and method of ore discharge
Initial
Final period
a winding valley in the narrow mountains
Wide valley, single or double side ore
Flat or hillside tailings pond, three or four sides of the mine
0.30
0.40
0.50
0.60~0.70
0.70~0.80
0.80~0.90
The tailings density of this watch is the data when γg=2.7. If γg is not 2.7, then the correction coefficient β needs to be multiplied;

γ
β=——
2.7

In addition, according to domestic experience, the gamma value data of this table is too large, and the lower limit is generally appropriate.

Tapered Roller bearings are radial thrust rolling bearings with tapered roller. There are two kinds of cone angle and big cone angle .Small cone angle mainly bear radial direction load primarily radial and axial loads, often used in pairs, reverse installation, inner and outer ring can be installed separately, in installation using radial and axial clearance can be adjusted; Big cone angle mainly bear axial load primarily of axial and radial load, is generally not used to bear alone the pure axial load, as to the pair (end with the same relative installation) can be used to carry pure radial load.

tapered 1


Tapered roller bearings are widely used in automobile, rolling mill, mining, metallurgy, plastic machinery and other industries.

tapered 2

Range of size are below:

Single row tapered roller bearing:

Inner diameter range: 20mm ~ 1270mm.

Outer diameter range: 40mm ~ 1465mm.

Width: 15mm ~ 240mm.

Double row tapered roller bearing:

Inner diameter range: 38mm ~ 1560mm.

Outer diameter range: 70mm ~ 1800mm.

Width: 50mm ~ 460mm.

Four row tapered roller bearings:

Inner diameter range: 130mm ~ 1600mm.

Diameter range: 200mm ~ 2000mm.

Width: 150mm ~ 1150mm.

The precision we can produce P0~P2.


We believe that we can supply the best service and price for your, hope to make a long-term cooperation with you. If you have any question please do not hesitate contact with us. We keep warmly welcome you visit us in any time.



Tapered Roller Bearing

Tapered Roller Bearing,Roller Bearing,Taper Bearing,Tapered Roller

LUOYANG AUTO BEARING CO.,LTD , https://www.ballbearing.nl